Rife/Beck Zapper
Blood Electrification Instructions
The idea behind these instructions is to give you a guideline for
amount of usage to match your bodys amount of resultant cleansing
so that you don't try to do too much too soon and get sick from
excess toxins. The liver & kidneys will cleanse the blood of
deactivated viruses/bacteria/yeast but only at a rate that is
unique to you. Therefore you should start out slowly and every week
increase usage time if you feel up to it.
Recommendations
For most people treatment lasts for 2 months to get rid of a systemic
viral infection (such as Epstein Barr virus which causes chronic fatigue
syndrome), but the only real goal is to keep on using the unit until you
don't experience cleansing reactions (headache, tiredness, achiness)
anymore. It is safe to use it indefinitely also. The inventor used
his every day for 2 years to make sure there would be no bad
effects from extended usage. Use the following protocol: Start by
using the unit the first week daily for 15 minutes. (If you are
bed-ridden, start at 10 minutes daily for one week, then advance to
20 minutes if cleansing reactions are minimal.) Then use it for 30
minutes daily the 2nd week. If you no longer feel very toxic (with
headaches, tiredness, etc.) start using it for one hour daily the
3rd week. If you have an immune dysfunction disease or are
circulation impaired, then step up usage at a slower rate. If you
start getting too toxic then use it only 15 minutes for one day and
drink a lot of water or celery juice and take as a diuretic
watermelon, cucumber, or parsley tea. You alone determine the pace
you need. Don't go so fast that you overly sicken yourself with
excess cleansing reactions. If you don't start out slow the first 2
weeks then you may overly burden your immune system so that you
could get sick from some infection. Haste makes waste. Go slow.
It is OK to break up usage into 2 sessions a day. If you've used it
for 2 months and are still getting
cleansing reactions from it then you should continue using it daily
until you no longer get those reactions. Make sure it is used every
day without skipping any. AIDS patients need to use it the same
time every day (+/- 2hrs) because HIV has a 1.2 day life cycle. If
you skip a day then you'll have to continue using it for at least
21 days from that skipped day because of the 21 day life cycle of
most viruses. Don't skip a day! If you are taking potent drugs
and/or herbs more than once a day or just don't want to cause any
transfection effects in your blood
cells (which is normal when using the lower frequencies) then use a
frequency between 30 and 90 hz. Otherwise use a lower frequency all
the way down to 4 hz, keeping in mind that the lower the frequency
the more potent it is and the more transfection it causes. Beck
personally prefered 4hz although it does
cause transfection. With 30hz when you have worked up to 2 hours a
day and when you no longer get bad reactions then you should try 4
hz to see if you get any cleansing reactions. If you do, then you'll
need to continue using it until you no longer get those reactions.
With 4-10 hz, if you are taking herbs or medicines (or coffee,
alcohol, smoking, vit's A + D in large doses) then you'll have to
use it in the morning or just before taking them so the blood will
be clean during the transfection effect and the blood cells won't
get overdosed with chemicals.
It may be helpful if you encouraged yourself daily to resist the
tendency to become skeptical and give up. Do this by thinking
positive thoughts about the new life you'll have once you've
regained your health. It will be definitely worth any trouble
encountered. Life can be so sweet when vitality brightens every
moment of your existence.
Usage Instructions
To test for proper operation and strength of batteries: Flip the
power switch to the ON position and set the frequency to below 10
hz. Press the Test button down and look at the Test Light to see
that it is alternating in color between red and green. (At higher
frequencies the light will be green on one side and red on the
other). If the five 9 volt batteries need replacement the Test
Light will not light at all. To replace the batteries just use a
phillips screwdriver to unscrew the cases bottom 4 screws, pull off
the cover, and then pull off the snap clips from each battery so
that they can be replaced with new alkaline ones. Reinstall the
padding as it was so as to prevent the batteries from rattling when
the box is jiggled. (Click here
for drawing). Panasonic batteries aren't recommended since
they are really hard to remove from the battery snaps.
Choosing electrode site: Both electrodes on the inside of
one wrist is the easiest site for convenient usage, but it affects
the least amount of blood. But for some people the wrist is the
preferred electrode site because it will allow more electrical
current than other arrangements. Using one electrode on one wrist
and the second one on the other wrist is my favorite because plenty
of blood is affected. The only worry for some people might be any
disliking of the electrical current by the heart (although most of
the current travels through the blood and not through the heart
muscles). The best electrode placement for wrist-to-wrist is on the
little finger side (read below). Using the electrodes on both
ankles affects the most amount of blood, but will barely allow
enough electrical current for some people (due to mineral deficiencies)
and is hardest for initiating and maintaining correct placement.
Locating electrode placement sites for one wrist: The
locations on the two main arteries is on the inner side of either
wrist about 1+1/2 inches below the wrist crease to the outside of
the main tendons, between them and the bones. Over these arteries,
starting about 1" from the crease, is where the electrodes should
be placed. (Avoid placing electrodes directly over the thumb side
tendon to prevent muscular twitching during use.) The placement
site for the little finger side is actually more on the side of the
wrist. (picture)
Locating electrode placement sites for both wrists: The
locations are the inner side of the wrists about 1+1/2 inches below
the wrist crease to the outside of the main tendons. Each wrist
should have one electrode held in place by one wrist band. (picture)
Locating electrode placement sites for ankles: On the inner
side of each foot locate the pulse of the unseen artery between the
ankle and the heel. If you can't feel it then go for a brisk walk
for ten minutes and then feel for it without elevating your foot.
On top of these pulsating arteries are the sites. (picture)
Connecting Electrodes: Clean & dry the electrode sites. Soak each
of the cloth electrodes thoroughly with tapwater or 1/2 eyedropper
of saltwater. Squeeze the middle of the insulation of the Blood Electrifiers
alligator clips (at the end of its wires) so that you open the jaws
and then let them bite onto the electrodes ends. (picture)
Place the electrode over the artery.
Then put the elastic band around it and the wrist. Don't
pull it tight. Just enough stretch to keep it in place is good.
If using electrodes on the ankles, then attach them there with 1" wide
medical tape. Re-wet the top end of cloth electrode after 1 hour of use. Make
sure no metal touches your skin which can cause a slight electrical burn.
Making Saltwater: If your tap water isn't very electrically
conductive then you may want to make and use saltwater which is
very conductive although corrosive to the electrodes and alligator
clips. Make concentrated saltwater by stirring 3 tsp non-iodized
sea salt or rock salt into 2 ounces distilled water. Stir 1 drop of
this salt solution into 4 oz distilled water and use to fill an
eyedropper bottle.
Using the device: Connect the wet electrodes to you. Turn
the dial to the lowest setting (CCW), flip the switch to the ON
position, and set the frequency output at 4hz. Turn the dial CW until
the green current light comes on fully. (Then you can change the frequency
to that which you want to use.)
This light will indicate when you are getting at least 75ua through
your bloodstream with both electrodes on one wrist, and 150ua
through the bloodstream with electrodes ankle-to-ankle or
wrist-to-wrist. (50ua is the bare minimum needed to do the job but
more current equals less treatment time needed.) If it won't light
at maximum dial position then one of three conditions exist; 1)
Your body's salt & mineral level is very low, 2) Where you
placed the electrodes is unsuitable, 3) The tap water isn't very
conductive and you need to use saltwater. If your salt level is low
then start salting your food with sea salt. If the electrodes
'sting' or 'bite' then 1) dial setting is too high, 2) skin is
dirty, 3) bare metal of the alligator clips are
touching your skin, 4) you need to relocate them, 5) there's too
much accumulated salt in the electrodes from dozens of previous
uses. To clean them, just boil 1 cup water, turn off heat, add 5
drops Clorox, and then drop the electrodes in to let the salt leach
out into the water for 30 minutes. Squeeze them dry when
finished.
Comfort Suggestions: If your skin becomes irritated where
the electrodes were then maybe you're applying too much current or
not cleaning the skin beforehand. Just apply vitamin E oil
afterwards to the skin.
Electrode storage: Store electrodes in plastic that's
allowed to breath.
Device warranty: 1 year parts and labor.
Look at our warranty page for
instructions on returning the unit to us.
Click here for instructions on treating hepatitis.
|
